|
|
|
# Програмне забезпечення для проектування і розрахунку
# Програмне забезпечення для моделювання продукції
# Програмне забезпечення для виробництва; інше
# Програмне забезпечення та рішення для загальної промисловості |
Рік заснування : |
1984 |
Рід діяльності : |
Manufacturer |
З 1984 року ми розробляємо наші програми в тісному співробітництві зі сходів виробників. Як наслідок, вона послідовно відповідність з їх потребами. Тому більш ніж 1000 клієнтів довіряють нашою мовою.
Не витрачайте час на проектування сходів вручну! З нашою програмою ви плануєте сходах протягом декількох хвилин. Ви отримаєте точні міліметра 1:1 відбитки рядків, перила, сходи і посади.
Крім того, подальшої підготовки роботи сприяє нашої програми. Програмне забезпечення здійснює пропонуємо листи, woodlists і оптимізовані різання листів. За допомогою обчислення необхідних деревини для розрахунку!
З метою оптимізації виробництва сходів, наша програма генерує ЧПУ даних для всіх загальних центрів обробки бажанням.
Далі можна уявити сходами з кольоровими і дерево текстури.
Програмне забезпечення Wagemeyer Сходи допоможе вам при плануванні, проектуванні і розрахунку сходів!
| Designing stairs with the computer With our program you design straight, quarter-turn, half-turn, two-quarter-turn and three-quarter-turn staircases as well as S-shaped staircases within a few minutes. At installation time, the default settings for stairs used in your company are prepared to be used by the program. As a consequence, a really fast design of your stairs is ensured.
After feeding the program with the basic data of the actual stair, the program calculates a suggestion for the going line. Moreover, all relevant staircase data (e.g. going, number of rises, rise, headroom) are shown to you. All calculations are based on the valid standards for the building of stairs, as far as these can be pre-set in the program. If due to the specific data of a stair these standards cannot be kept, the program indicates that this is the case.
Following this, a suggestion for the structure of the staircase is given by the program. Normally, you can accept this suggestion without further changes. However, if it does not correspond to what you have in your mind, there is a variety of possibilities to change the structure of the staircase - determine the method used by the program to calculate the structure (constant / linear / parabolic), or change the minimum going, or even change the structure by hand. |
| The spindle program Designing stairs with the computer
Design spiral staircases in a few minutes. The program reads out the default values of your production line, e.g. stage strength, column diameter and hand rail mass and transfers this as defaults. Sure, these defaults can be individually entered also for each stairs.
Indicate simply the desired stair diameter and correct the suggestion after customer's request. The construction is final already.
Of course it is also possible to indicate around the stages or adapt only the landing to its process a cover hole.
Now you have the following possibilities of the expenditure:
1:1-print of steps and handrails
Step plates 1:10
Assembly drawing with the most important statements
For the metalworkers we offer an appropriate steel spindle version. With this landing sub-constructions in V and stage sub-constructions in T-form are spent, which on a scale 1:10 are printed out.
| |
|
|